View AD9289_562520.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary Technical Data
FEATURES
* Four ADCs in one package * Serial LVDS digital output data rates up to 520 Mbps (ANSI644) * Data clock output provided * SNR = 47 dB (to Nyquist) * Excellent Linearity: DNL = 0.25 LSB (Typical) * * * * * INL = 0.5 LSB (Typical) 400 MHz full power analog bandwidth Power dissipation = 112 mW Core ADC Power per channel at 65 MSPS 1 Vpp - 2 Vpp input voltage range +3.0 V supply operation Power down mode
VIN+D VIN-D VREF SENSE REFT_A REFB_A REFT_B REFB_B VIN+A VIN-A
Quad 8-Bit, 65 MSPS Serial LVDS 3V A/D Converter AD9289
FUNCTIONAL BLOCK DIAGRAM
AVDD DRGND PDWN S1 DRVDD OR+ OR-
AD9289
SHA Pipeline ADC
8 Serial LVDS D1+A D1-A
8 SHA Pipeline ADC Serial LVDS
D1+D D1-D
LVDSBIAS LOCK Ref Select
+ -
0.5 V
Data Rate Multiplier FCO+ FCO- CLK+ CLK-
DCO+ DCO-
SHARED_REF CML AGND
APPLICATIONS
* Tape drives * Medical imaging
Figure 1. Functional Block Diagram
PRODUCT HIGHLIGHTS
1. 2. 3. 4. 5. Four analog-to-digital converters are contained in one small, space saving package. A Data Clock Out (DCO) is provided which operates up to 260 MHz. The outputs of each ADC are serialized and provided on the rising and falling edge of DCO). Output data rates up to 520 Mbps (8 bits x 65 MSPS) are available. The AD9289 operates from a single 3V power supply. The clock duty cycle stabilizer maintains performance over a wide range of input clock duty cycles
AD9289 R1 2.3MHz Typical at Nominal Conditions, 2VFS Int Ref SNR = 49.1dB, SFDR = 71.9dB
0 -10
PRODUCT DESCRIPTION
The AD9289 is a quad 8-bit, 65 MSPS analog-to-digital converter with an on-chip track-and-hold circuit and is designed for low cost, low power, small size and ease of use. The product operates up to 65 MSPS conversion rate and is optimized for outstanding dynamic performance where a small package size is critical. The ADC requires a single+3V power supply and an LVDS compatible sample rate clock for full performance operation. No external reference or driver components are required for many applications. A separate output power supply pin supports LVDS compatible serial digital output levels. The ADC automatically multiplies up the sample rate clock for the appropriate LVDS serial data rate. An FCO trigger is provided to signal a new output byte. Power down is supported, and the ADC consumes less than 10mW when enabled. Fabricated on an advanced CMOS process, the AD9289 is available in a 64-ball mini-BGA package (64 CSP_BGA) specified over the industrial temperature range (-40C to +85C).
-20 -30 -40 -50 -60 -70 -80 -90 -100 0 5 10 15 20 25 30
Figure 2. Measured FFT
Rev. PrJ
6/25/2004 One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies.
AD9289
TABLE OF CONTENTS
AD9289--Specifications ............................................................ 3 DIGITAL SPECIFICATIONS ................................................. 4 AC SPECIFICATIONS........................................................... 4 SWITCHING SPECIFICATIONS ........................................... 5 EXPLANATION OF TEST LEVELS ...................................... 5 Absolute Maximum Ratings ........................................................ 6 Definitions ................................................................................. 7 Theory of Operation ................................................................... 9 Clock Input............................................................................. 9 Analog Inputs ......................................................................... 9
Preliminary Technical Data
Voltage Reference....................................................................9 Internal Reference Connection ...............................................10 External Reference Operation ................................................10 Digital Outputs ...................................................................... 11 Timing .................................................................................. 11 PLL LOCK Output ................................................................ 11 CML Pin ............................................................................... 11 Overange............................................................................... 11 Pin Configurations ....................................................................13 Timing Diagram........................................................................14 Ordering Guide .....................................................................16
REVISION HISTORY
Revision PrA: Initial Version Revision PrB: Updated specifications Revision PrC: Added application section Revision PrD: Revised block diagram, added LOCK/ output to timing diagram, added offset and gain matching definitions, updated Theory of Operation Revision PrE: Updated timing diagram and PLL description Revision PrF: Updated Timing Specs, Pin Function Description (Added DNC pins), Added Pin Configuration Diagram and Package Outline Revision PrG: Added DCR pin info, updated lvdsbias resistor value, Revision H: Updated reference description, Removed S3, Added scope plot, Added FFT, Updated Tpd, Tcpd, Tmsb, Power, Updated LVDSBIAS Resistor value, Min Encodea 20MSPS Revision I: Updated Power Supply Range, Added thermal impedance number, Revision J: Added CML description, Modified Timing Diagram, Changed MSB naming to FCO,Removed S2, Modified Tpd,
Rev. PrJ | Page 2 of 16
6/25/2004
Preliminary Technical Data
AD9289--SPECIFICATIONS
Parameter
RESOLUTION No Missing Codes Offset Matching Gain Matching ACCURACY
2
AD9289
1
AVDD = 3.0V, DRVDD = 3.0V; INT REF; DIFFERENTIAL ANALOG AND CLOCK INPUTS
Temp
Full 25C 25C 25C Full 25C Full Full Full Full 25C Full Full Full Full Full Full Full Full Full Full Full 25C Full Full Full
Table 1
Test Level
VI I I I VI I VI V V V I V V V V V V V IV IV VI VI I VI VI V
Min
Typ
8 Guaranteed 25 2 0.25 0.5 16 150 0.5
Max
Unit
Bits mV % FS LSB LSB LSB LSB ppm/C ppm/C ppm/C V uA uA
Differential Nonlinearity (DNL) Integral Nonlinearity (INL) Offset Error 2 Gain Error Reference Internal Reference Voltage
TEMPERATURE DRIFT
REFERENCE
ANALOG INPUTS
Output Current Input Current Input Resistance Differential Input Voltage Range Common Mode Voltage Input Resistance Input Capacitance Analog Bandwidth, Full Power AVDD DRVDD Power Dissipation3 Power Down Dissipation Power Supply Rejection Ratio (PSRR) IAVDD3 DRVDD3 Crosstalk
7 1 -2 1.5 tbd 5 400 3.0 3.0 558 <10
2.85 2.85
3.15 3.15
POWER SUPPLY
k Vpp V k pF MHz V V mW mW mV/V mA mA dB
CROSSTALK
150 36 70
1 2 3
Specifications subject to change without notice Gain error and gain temperature coefficients are based on the ADC only (with a fixed 0.5 V external reference and a 1 V p-p differential analog input). Power dissipation measured with rated encode and a dc analog input (Out puts Static, IVDD = 0.). IVCC and IVDD measured with TBD MHz analog input @ 0.5dBFS. Rev. PrJ | Page 3 of 16 6/25/2004
AD9289
DIGITAL SPECIFICATIONS
AVDD = 3.0V, DRVDD = 3.0V
Parameter
Differential Input Voltage Input Common Mode Voltage Input Resistance Input Capacitance Logic `1' Voltage Logic `0' Voltage Input Resistance Input Capacitance Differential Output Voltage (VOD ) Output Offset Voltage (VOS) Output Coding
1
Preliminary Technical Data
Temp
Full Full Full 25C Full Full Full Full Full Full Full
Test Level
IV IV IV IV IV IV IV IV IV IV IV
Min
247
Typ
Max
Unit
mVpp V k pF
CLOCK INPUTS (CLK+, CLK-)
1.25
2.0 0.8 30 4 247 454 1.125 1.375 Twos Complement or Binary
LOGIC INPUTS
V V k PF mV V
DIGITAL OUTPUTS (LVDS Mode)
Table 2: Digital Specifications
AC SPECIFICATIONS2
AVDD = 3.0 V, DRVDD = 3.0 V; INTERNAL REF; DIFFERENTIAL ANALOG AND CLOCK INPUT, LVDS OUTPUT MODE
Parameter
fIN = 10.3 MHz SIGNAL TO NOISE RATIO (SNR) - Without Harmonics fIN = 19.6 MHz fIN = 32.5 MHz fIN = 51 MHz fIN = 10.3 MHz SIGNAL TO NOISE RATIO (SINAD) - With Harmonics fIN = 19.6 MHz fIN = 32.5 MHz fIN = 51 MHz fIN = 10.3 MHz EFFECTIVE NUMBER OF BITS (ENOB) fIN = 19.6 MHz fIN = 32.5 MHz fIN = 51 MHz fIN = 10.3 MHz SPURIOUS FREE DYNAMIC RANGE (SFDR) fIN = 19.6 MHz fIN = 32.5 MHz fIN = 51 MHz fIN = 10.3 MHz SECOND AND THIRD HARMONIC DISTORTION fIN = 19.6 MHz fIN = 32.5 MHz fIN = 51 MHz fIN = 10.3 MHz TOTAL HARMONIC DISTORTION (THD) fIN = 19.6 MHz fIN = 32.5 MHz fIN = 51 MHz
1 2
Temp
25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C
Test Level
V V I V V V I V V V I V V V I V V V I V V V I V
Min
Typ
47.5 47.5 47 47 7.5 7.5 62 59 62 59 60 58
Max
Unit
dB dB dB dB dB dB dB dB Bits Bits Bits Bits dB dB dB dB dBc dBc dBc dBc dBc dBc dBc dBc
Clock Inputs are LVDS compatible .Clock Inputs require external DC bias and cannot be AC coupled. SNR/harmonics based on an analog input voltage of -0.5 dBFS referenced to a 1 Vpp full-scale input range. Rev. PrJ | Page 4 of 16 6/25/2004
Preliminary Technical Data
Parameter
TWO TONE INTERMOD DISTORTION (IMD) fIN1= 19 MHz, fIN2= 20 MHz fIN1= xx MHz, fIN2= xx MHz
AD9289
Temp
25C 25C
Test Level
V V
Min
Typ
Max
Unit
dBc dBc
Table 3: AC Specifications
SWITCHING SPECIFICATIONS
AVDD = 3.0 V, DRVDD = 3.0 V; DIFFERENTIAL ENCODE INPUT
Parameter
Maximum Clock Rate Minimum Clock Rate Clock Pulse Width High (tEH ) Clock Pulse Width Low (tEL) 1 Valid Time (tV) 1 Propagation Delay (tPD ) MSB Propagation Delay (tMSB) 1 Rise Time (tR ) (20% to 80%) Fall Time (tF ) (20% to 80%) DCO Propagation Delay (tCPD ) Data to DCO Skew (tPD - tCPD ) Pipeline Latency Aperture Delay (tA) Aperture Uncertainty (Jitter)
Temp
Full Full Full Full Full Full Full Full Full Full Full Full 25C 25C
Test Level
VI VI IV IV VI VI VI V V VI IV VI V V
Min
65
Typ
Max
20
Unit
MSPS MSPS ns ns ns ns ns ns ns ns pS cycles ps ps rms
CLOCK
6.9 6.9 10 10 0.5 0.5 10
+/- 100
OUTPUT PARAMETERS IN LVDS MODE
6 <1
APERTURE
Table 4: Switching Specifications
EXPLANATION OF TEST LEVELS
TEST LEVEL
I II III IV V VI 100% production tested. 100% production tested at +25C and guaranteed by design and characterization at specified temperatures. Sample Tested Only Parameter is guaranteed by design and characterization testing. Parameter is a typical value only. 100% production tested at +25C and guaranteed by design and characterization for industrial temperature range.
1
tV and tPD are measured from the transition points of the CLK input to the 50%/50% levels of the digital outputs swing. The digital output load during test is not to exceed an ac load of 5 pF or a dc current of 40 A. Rise and fall times measured from 20% to 80%. Rev. PrJ | Page 5 of 16 6/25/2004
AD9289
ABSOLUTE MAXIMUM RATINGS
Parameter
AVDD Voltage DRVDD Voltage Electrical Analog Input Voltage Analog Input Current Digital Input Voltage Digital Output Current VREF Input Voltage Operating Temperature Range (Ambient) Maximum Junction Temperature Environmental Lead Temperature (Soldering, 10 sec) Maximum Case Temperature Storage Temperature Range (Ambient) 1 Thermal Impedance
Table 5: Absolute Maximum Ratings
Preliminary Technical Data
Rating
-40C to +85C
40C/W
Stresses above those listed under the Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
1
ja for a 4 layer PCB with solid ground plane in still air.
Rev. PrJ | Page 6 of 16
6/25/2004
Preliminary Technical Data
DEFINITIONS
ANALOG BANDWIDTH
The analog input frequency at which the spectral power of the fundamental frequency (as determined by the FFT analysis) is reduced by 3 dB.
AD9289
pulse (CLK+) should be left in logic "1" state to achieve rated performance; pulse width low is the minimum time the clock pulse should be left in low state. See timing implications of changing t clk in text. At a given clock rate, these specs define an acceptable clock duty cycle.
APERTURE DELAY
The delay between the 50% point of the rising edge of the ENCODE command and the instant at which the analog input is sampled.
FULL SCALE INPUT POWER
Expressed in dBm. Computed using the following equation:
2 VFullscale rms Z Input = 10 log .001
APERTURE UNCERTAINTY (JITTER)
The sample -to-sample variation in aperture delay.
PowerFullscale

CROSSTALK
Coupling onto one channel being driven by a low level (-40 dBFS) signal when the adjacent interfering channel is driven by a fullscale signal.
GAIN ERROR
Gain error is the difference between the measured and ideal full scale input voltage range of the worst ADC.
DIFFERENTIAL ANALOG INPUT RESISTANCE, DIFFERENTIAL ANALOG INPUT CAPACITANCE, AND DIFFERENTIAL ANALOG INPUT IMPEDANCE
The real and complex impedances measured at each analog input port. The resistance is measured statically and the capacitance and differential input impedances are measured with a network analyzer.
GAIN MATCHING
Expressed in %FSR. Computed using the following equation:
GainMatching =
FSR max - FSR min * 100% FSR max + FSR min 2
DIFFERENTIAL ANALOG INPUT VOLTAGE RANGE
The peak to peak differential voltage that must be applied to the converter to generate a full scale response. Peak differential voltage is computed by observing the voltage on a single pin and subtracting the voltage from the other pin, which is 180 degrees out of phase. Peak to peak differential is computed by rotating the inputs phase 180 degrees and taking the peak measurement again. Then the difference is computed between both peak measurements.
where FSRmax is the most positive gain error of the ADCs and FSRmin is the most negative gain error of the ADCs.
HARMONIC DISTORTION, SECOND
The ratio of the rms signal amplitude to the rms value of the second harmonic component, reported in dBc.
HARMONIC DISTORTION, THIRD DIFFERENTIAL NONLINEARITY
The deviation of any code width from an ideal 1 LSB step. The ratio of the rms signal amplitude to the rms value of the third harmonic component, reported in dBc.
EFFECTIVE NUMBER OF BITS
The effective number of bits (ENOB) is calculated from the measured SNR based on the equation:
INTEGRAL NONLINEARITY
The deviation of the transfer function from a reference line measured in fractions of 1 LSB using a "best straight line" determined by a least square curve fit.
ENOB =
SNR MEASURED - 1.76dB 6.02
MINIMUM CONVERSION RATE
The encode rate at which the SNR of the lowest analog signal frequency drops by no more than 3 dB below the guaranteed limit.
CLOCK PULSE WIDTH/DUTY CYCLE
Pulse width high is the minimum amount of time that the Clock
Rev. PrJ | Page 7 of 16 6/25/2004
AD9289
MAXIMUM CONVERSION RATE
The encode rate at which parametric testing is performed.
Preliminary Technical Data
SIGNAL-TO-NOISE RATIO (WITHOUT HARMONICS)
The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, excluding the first five harmonics and dc.
OFFSET ERROR
Offset error is the difference between the measured and ideal voltage at the analog input that produces the midscale code at the outputs. Offset error is given for the worst ADC.
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
The ratio of the rms signal amplitude to the rms value of the peak spurious spectral component. The peak spurious component may or may not be a harmonic. It also may be reported in dBc (i.e., degrades as signal level is lowered) or dBFS (i.e., always related back to converter full scale).
OFFSET MATCHING
Expressed in mV. Computed using the following equation:
OffsetMatching = OFF max - OFF min
where OFFmax is the most positive offset error and OFFmin is the most negative offset error.
TWO-TONE INTERMODULATION DISTORTION REJECTION
The ratio of the rms value of either input tone to the rms value of the worst third order intermodulation product; reported in dBc.
OUTPUT PROPAGATION DELAY
The delay between a differential crossing of CLK+ and CLK- and the time when all output data bits are within valid logic levels.
TWO-TONE SFDR
The ratio of the rms value of either input tone to the rms value of the peak spurious component. The peak spurious component may or may not be an IMD product. It also may be reported in dBc (i.e., degrades as signal level is lowered) or in dBFS (i.e., always relates back to converter full scale).
NOISE (FOR ANY RANGE WITHIN THE ADC)
V noise =
Z * .001 * 10
FS dBm - SNRdBc - SignaldBFS 10
WORST OTHER SPUR
The ratio of the rms signal amplitude to the rms value of the worst spurious component (excluding the second and third harmonic) reported in dBc.
Where Z is the input impedance, FS is the full scale of the device for the frequency in question, SNR is the value for the particular input level and Signal is the signal level within the ADC reported in dB below full scale. This value includes both thermal and quantization noise.
TRANSIENT RESPONSE TIME
Transient response time is defined as the time it takes for the ADC to reacquire the analog input after a transient from 10% above negative full scale to 10% below positive full scale.
POWER SUPPLY REJECTION RATIO
The ratio of a change in input offset voltage to a change in power supply voltage.
SIGNAL-TO-NOISE-AND-DISTORTION (SINAD)
The ratio of the rms signal amplitude (set 1 dB below full scale) to the rms value of the sum of all other spectral components, including harmonics but excluding dc.
OUT-OF-RANGE RECOVERY TIME
Out of range recovery time is the time it takes for the ADC to reacquire the analog input after a transient from 10% above positive full scale to 10% above negative full scale, or from 10% below negative full scale to 10% below positive full scale.
Rev. PrJ | Page 8 of 16
6/25/2004
Preliminary Technical Data
THEORY OF OPERATION
Each A/D converter in the AD9289 architecture consists of a frontend sample and hold amplifier (SHA) followed by a pipelined switched capacitor A/D converter. The pipelined A/D converter is divided into two sections, consisting of six 1.5-bit stages and a final 3-bit flash. Each stage provides sufficient overlap to correct for flash errors in the preceding stages. The quantized outputs from each stage are combined into a final 8-bit result in the digital correction logic. The pipelined architecture permits the first stage to operate on a new input sample while the remaining stages operate on preceding samples. Sampling occurs on the rising edge of the clock. Each stage of the pipeline, excluding the last, consists of a low resolution flash A/D connected to a switched capacitor DAC and interstage residue amplifier (MDAC). The residue amplifier magnifies the difference between the reconstructed DAC output and the flash input for the next stage in the pipeline. One bit of redundancy is used in each one of the stages to facilitate digital correction of flash errors. The last stage simply consists of a flash A/D. The input stage contains a differential SHA that can be configured as ac- or dc-coupled in differential or single -ended modes. The output-staging block aligns the data, carries out the error correction and passes the data to the output buffers.During power-down the output buffers go into a high-impedance state.
AD9289
output driver supplies to avoid modulating the clock signal with digital noise. Low jitter, crystal-controlled oscillators make the best clock sources. If the clock is generated from another type of source (by gating, dividing, or other methods), it should be retimed by the original clock at the last step.
Analog Inputs
For best dynamic performance, the source impedances driving VIN+ and VIN- should be matched such that common-mode settling errors are symmetrical. These errors will be reduced by the common-mode rejection of the A/D.
Voltage Reference
A stable and accurate 0.5 V voltage reference is built into the AD9289. The input range can be adjusted by varying the reference voltage applied to the AD9289, using either the internal reference or an externally applied reference voltage. The input span of the A/D tracks reference voltage changes linearly. The Shared Reference mode allows the user to connect the references from the quad ADC together externally for superior gain and offset matching performance. If the ADCs are to function independently, the reference decoupling can be treated independently and can provide superior isolation between the four channels. To enable Shared Reference mode, the SHARED_REF pin must be tied high and external differential references must be externally shorted. (REFT_A must be externally shorted to REFT_B and REFB_A must be shorted to REFB_B.) Note that channels A and B are referenced to REFT_A and REFB_A and channels C and D are referenced to REFT_B and REFB_B.
Clock Input
Typical high-speed A/D converters use both clock edges to generate a variety of internal timing signals, and as a result may be sensitive to clock duty cycle. Commonly a +/-5% tolerance is required on the clock duty cycle to maintain dynamic performance characteristics. The AD9289 contains a clock duty cycle stabilizer that retimes the non-sampling edge, providing an internal clock signal with a nominal 50% duty cycle. This allows a wide range of clock input duty cycles without affecting the performance of the AD9289. As shown in TPC XX, noise and distortion performance are nearly flat over at least a +/-15% range of duty cycle. The stabilizer circuit can be bypassed by grounding input pin DCR. ( There is an internal 22K ohm pull-up resistor) The duty cycle stabilizer uses a delay-locked loop (DLL) to create the non-sampling edge. As a result, any changes to the sampling frequency will require approximately 100 clock cycles to allow the DLL to acquire and lock to the new rate. High-speed, highresolution A/Ds are sensitive to the quality of the clock input. The degradation in SNR at a given full-scale input frequency (fA) due only to aperture jitter (tA) can be calculated with the following equation:
SNR degradation = 20 x log10 [1/2 x pi x fA x tA]
In the equation, the rms aperture jitter, tA, represents the root sum square of all jitter sources, which include the clock input, analog input signal, and A/D aperture jitter specification. Undersampling applications are particularly sensitive to jitter. The clock input should be treated as an analog signal in cases where aperture jitter may affect the dynamic range of the AD9289. Power supplies for clock drivers should be separated from the A/D
Rev. PrJ | Page 9 of 16
Figure 3. Shared Reference Mode
6/25/2004
AD9289
Internal Reference Connection
A comparator within the AD9289 detects the potential at the SENSE pin and configures the reference into four possible states, which are summarized in Table I. If SENSE is grounded, the reference amplifier switch is connected to the internal resistor divider (see Figure 2), setting VREF to 1 V. Connecting the SENSE pin to VREF switches the reference amplifier output to the SENSE pin, completing the loop and providing a 0.5 V reference output. If a resistor divider is connected as shown in Figure 3, the switch will again be set to the SENSE pin. This will put the reference amplifier in a non-inverting mode with the VREF output defined as follows: VREF = .5 * (1 +R2/R1) In all reference configurations, REFT and REFB drive the ADC core and establish its input span. The input range of the ADC always equals twice the voltage at the reference pin for either an internal or an external reference.
Preliminary Technical Data
Figure 5.Programmable Reference Connection
External Reference Operation
The use of an external reference may be necessary to enhance the gain accuracy of the ADC or improve thermal drift characteristics. When multiple ADCs track one another, a single reference (internal or external) may be necessary to reduce gain matching errors to an acceptable level. A high precision external reference may also be selected to provide lower gain and offset temperature drift. External reference mode is chosen by tying SENSE pin to AVDD and driving VREF with external reference.
Figure 4.Internal Reference Connection
Rev. PrJ | Page 10 of 16
6/25/2004
Preliminary Technical Data
X Selected Mode SENSE Voltage Internal Switch Position Resulting VREF (V)
AD9289
Resulting Differential Span (V p-p) 2 x External Reference 1.0 2 x VREF 2.0
External Reference Internal Programmable Internal
AVDD VREF 0.2 V to VREF AGND to 0.2 V
N/A SENSE SENSE Internal Divider
N/A 0.5 0.5 x (1 + R2/R1) 1.0
Table 1 Reference Settings
of DCO. The FCO clock is used to signal the start of a new output byte and is equal to the sampling clock rate. See the Timing Diagram for more information.
Digital Outputs
The AD9289's differential outputs conform to the ANSI-644 LVDS standard. To set the LVDS bias current, place a resistor (RSET is nominally equal to 3.8 k) to ground at the LVDSBIAS pin. The RSET resistor current (~ 1.2/RSET) is ratioed on-chip setting the output current at each output equal to a nominal 3.5 mA. A 100 differential termination resistor placed at the LVDS receiver inputs results in a nominal 350 mV swing at the receiver. The AD9289's LVDS outputs facilitate interfacing with LVDS receivers in custom ASICs and FPGAs that have LVDS capability for superior switching performance in noisy environments. Single point-to-point net topologies are recommended with a 100 termination resistor as close to the receiver as possible. It is recommended to keep the trace length no longer than 3 inches and to keep differential output trace lengths as equal as possible. The format of the output data can be selected as offset binary or twos complement. Pin S1 is used to set the format. S1 Mode AVDD AGND Data Format Twos Complement Offset Binary
PLL LOCK Output
The AD9289 contains an internal PLL that is used to generate the data clock out (DCO). When the PLL is locked, the LOCK/ signal will be low, indicating valid data on the outputs. If for any reason the PLL loses lock, the LOCK/ signal will go high as soon as the lock circuitry detects an unlocked condition. While the PLL is unlocked, the data outputs and DCO will remain in the last known state. If the LOCK/ signal goes high in the middle of a byte, no data or DCO signals will be available for the rest of the byte. It will take at least 1 s to regain lock if lock is lost. Once the PLL regains lock, the DCO will start. The first valid data byte will be indicated by the FCO signal. See the Timing Diagram for more information.
CML Pin
A common mode level output is available at F3. This output selfbiases to AVDD/2. This is a relatively high impedance output (two 5K resistors in series between AVDD and ground) with an output impedance of 2.5K which may need to be considered when using as a reference.
Table 6: S1 Configuration
Timing
Data from each A/D is serialized and provided on a separate channel. The data rate for each serial stream is equal to 8-bits times the sample clock rate, with a maximum of 520 MHz (8-bits x 65 MSPS = 520 MHz). The lowest typical conversion rate is 20 MSPS. Two output clocks are provided to assist in capturing data from the AD9289. The data clock out (DCO) is used to clock the output data and is equal to four times the sampling clock (CLK) rate. Data is clocked out of the AD9289 on the rising and falling edges
Overange
The AD9289 has an Overange output available that indicates when the ADC is driven out of range. OR+ is driven high in overrange condition, with the digital outputs are clamped to all zeroes or all ones.Pin Function Descriptions
Rev. PrJ | Page 11 of 16
6/25/2004
AD9289
Pin No.
C8 D8 F2, E4, F7 G2, E5, D7,E7,G7 C3, C6 D3, D6 H5 H4 F4 G4 F5 G5 E8 C7 G1 F1 H2 H3 H7 H6 A2,A4,A6, A8,B2,B4, B6,B8,D5, E1,E2,E3, F6,G6,H8
Preliminary Technical Data
Name
CLK+ CLKAVDD AGND DRVDD DRGND VREF SENSE REFT_A REFB_A REFT_B REFB_B PDWN S1 VIN+A VIN-A VIN+B VIN-B VIN+C VIN-C DNC (Do Not Connect)
*
Description
Input Clock - True Input Clock - Complement 3 V Analog Supply Analog Ground 3 V Digital Output Supply Digital Ground Voltage Reference Input/Output Reference Mode Selection Differential Reference (Positive) Differential Reference (Negative) Differential Reference (Positive) Differential Reference (Negative) Power Down Selection (set pin to
AVDD for power down)
Pin No.
G8 F8 C5 C4 C1 C2 B1 A1 B3 A3 B5 A5 B7 D1 D2 H1 G3 F3 D4 E6
Name
VIN+D VIN-D DCODCO+ FCO+ FCOD1+A D1-A D1+B D1-B D1+C D1-C D1+D OR+ ORLVDSBIAS SHARED_REF CML LOCK/ DCR
Description
ADC D Analog Input - True ADC D Analog Input - Complement Data Clock Output - Complement Data Clock Output - True Frame Clock Output (MSB Indicator) True Output Frame Clock Output (MSB Indicator) Complement Output ADC A True Digital Output ADC A Complement Digital Output ADC B True Digital Output ADC B Complement Digital Output ADC C True Digital Output ADC C Complement Digital Output ADC D True Digital Output Over Range True Over Range Complement LVDS Bias Resistor Pin (3.8K to gnd) Shared Reference Control Bit Common Mode Level Output ( = AVDD/2) PLL Lock Output Duty Cycle Control Enable Input Logic Hi enables duty cycle control circuit Logic Lo disables duty cycle control circuit
Data Format ADC A Analog Input - True ADC A Analog Input - Complement ADC B Analog Input - True ADC B Analog Input - Complement ADC C Analog Input - True ADC C Analog Input - Complement
Table 7: Pin Function Descriptions * S1 has an internal on-chip pulldown resistor
Rev. PrJ | Page 12 of 16
6/25/2004
Preliminary Technical Data
PIN CONFIGURATIONS
1 A B C D E F G H
Figure 6: BGA Top View
AD9289
2
34
567
8
Rev. PrJ | Page 13 of 16
6/25/2004
AD9289
TIMING DIAGRAM
Preliminary Technical Data
Figure 7: Timing Diagram
Measured Timing Encode = 65MHz
(DCO = 260MHz)
Rev. PrJ | Page 14 of 16
6/25/2004
Preliminary Technical Data
OUTLINE DIMENSIONS
AD9289
Figure 8: BGA Package Outline
Dim A A1 A2 D D1 E E1
Min. 1.35 0.25 1.10 7.90
Nom. 1.55 0.34 1.21 8.00 5.60 BSC
Max 1.70
Dim b e
Min. 0.45
Nom. 0.50
Max 0.55
0.80 BSC
0.10 0.10 0.12 0.15 0.08
1.31 8.10
aaa bbb ddd
7.90
8.00 5.60 BSC
8.10
eee fff
Rev. PrJ | Page 15 of 16
6/25/2004
AD9289
ESD CAUTION
Preliminary Technical Data
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Ordering Guide
Model AD9289BBC-65 AD9289BBC-65EB Temperature Range -40C to +85C (Ambient) 25C (Ambient) Description 64 CSP_BGA Evaluation Board
Table 8: Ordering Guide
(c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective companies. Printed in the U.S.A. PR03682-0-6/04(PrJ)
Rev. PrJ | Page 16 of 16
6/25/2004

▲Up To Search▲

Price & Availability of AD9289

	To Download AD9289 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .